amanbh997/skills-architects/construction-documentation

Construction Documentation

Construction documentation translates design intent into legally binding, buildable instructions. This skill covers every aspect of producing a complete, coordinated, and code-compliant set of construction documents -- from drawing organization and graphic standards through specifications, schedules, and the architect's role during the construction phase.

1. Drawing Set Organization

1.1 Standard Architectural Drawing Sequence

A complete architectural drawing set follows a consistent order that allows contractors, consultants, and reviewers to navigate the documents efficiently. The standard sequence is:

1. Cover Sheet -- project name, address, owner, architect, consultants,

project number, issue date, building code summary, occupancy classification, construction type, area tabulation, vicinity map.

1. Drawing List -- complete index of every sheet in the set, organized

by discipline with sheet number, title, and revision status.

1. General Notes -- project-wide notes, abbreviations, symbols legend,

material keynote legend, accessibility standards referenced, applicable codes and editions.

1. Site Plan -- property boundaries, setbacks, easements, building

footprint, grading, paving, landscaping, utilities, site lighting, stormwater management, accessibility routes.

1. Floor Plans -- every level including basement, ground, upper floors,

mezzanines, and mechanical penthouse. Show walls, doors, windows, stairs, elevators, room names, room numbers, dimensions, column grid, section cut indicators, elevation markers, detail callouts.

1. Reflected Ceiling Plans (RCP) -- ceiling materials, heights, grid

layout, light fixtures, diffusers, sprinkler heads, access panels, ceiling soffits, bulkheads.

1. Roof Plan -- roof slopes, drainage, overflow drains, mechanical

equipment, roof access, parapet heights, expansion joints, roof penetrations, fall protection anchorage.

1. Exterior Elevations -- all four sides minimum, material indications,

floor lines, ceiling lines, grade line, roof ridge/eave lines, window tags, door tags, material keynotes, vertical dimensions.

1. Building Sections -- longitudinal and transverse sections through

the entire building. Show structural system, floor-to-floor heights, foundation, roof structure, wall assemblies at cut, vertical circulation, key dimensions.

1. Wall Sections -- detailed vertical cuts through typical wall

assemblies from foundation to roof. Show every layer, flashing, waterproofing, insulation, vapor barriers, structural connections, window head/sill/jamb conditions.

1. Enlarged Plans -- stair plans, elevator plans, toilet rooms,

kitchens, lobbies, and other complex spaces at 1:50 or 1:20 scale.

1. Interior Elevations -- wall-by-wall interior views of significant

rooms: toilets, kitchens, reception areas, conference rooms. Show casework, tile layouts, fixture locations, outlet heights.

1. Stair and Elevator Details -- stair sections, handrail details,

guardrail connections, nosing profiles, elevator pit, shaft dimensions, machine room layout, cab interior elevations.

1. Door Schedule and Details -- door types, frame details, hardware

sets, threshold details, ADA clearance diagrams.

1. Window Schedule and Details -- window types, mullion details,

sill/head/jamb sections, hardware, performance specifications.

1. Finish Schedule -- room-by-room listing of floor, base, wall, and

ceiling finishes with finish codes cross-referenced to specifications.

1. Detail Sheets -- miscellaneous construction details not covered

elsewhere: expansion joints, control joints, flashing, waterproofing, miscellaneous metal, signage mounting.

1.2 Sheet Numbering Conventions

Sheet numbers use a discipline prefix followed by a category digit and sequential number. The standard architectural prefix is "A":

Other discipline prefixes:

• G -- General (project-wide cover sheets, code analysis)
• C -- Civil
• L -- Landscape
• S -- Structural
• M -- Mechanical
• P -- Plumbing
• FP -- Fire Protection
• E -- Electrical

1.3 Drawing Scale Conventions by Sheet Type

2. Drawing Standards

2.1 Line Weights

Consistent line weights ensure drawings are legible at all reproduction sizes. The standard hierarchy:

In practice, line weights map to pen colors in CAD systems:

• Color 1 (Red) = 0.13mm
• Color 2 (Yellow) = 0.18mm
• Color 3 (Green) = 0.25mm
• Color 4 (Cyan) = 0.35mm
• Color 5 (Blue) = 0.50mm
• Color 6 (Magenta) = 0.70mm

2.2 Text Heights

Text height standards ensure readability when plotted:

Font standards:

• Primary: Arial, Helvetica, or equivalent sans-serif
• CAD standard: SIMPLEX or ROMANS (SHX fonts)
• Avoid decorative fonts; maintain consistent font family across all sheets

2.3 Hatching Patterns

Standard material hatching in section and plan:

2.4 Annotation Standards

• Keynotes: Numeric references linked to keynote legend; preferred over

text notes for consistency. Use either sheet keynotes or reference keynotes (linked to specifications).

• Room Tags: Room number (bold, upper), room name (below), floor finish

code, ceiling height.

• Door Tags: Circle with door number referencing door schedule.
• Window Tags: Diamond or hexagon with window type referencing schedule.
• Section Markers: Circle with section number (upper) and sheet number

(lower), tail pointing in direction of view.

• Elevation Markers: Circle with arrow indicating viewing direction,

reference number and sheet number.

• Detail Callouts: Circle or oval with detail number (upper) and sheet

number (lower).

• Column Grid: Circles at grid intersections -- numbers for one axis

(1, 2, 3...) and letters for the other (A, B, C...).

2.5 Dimension Styles

Three primary dimensioning methods:

1. Running Dimensions (baseline): All dimensions taken from a single

reference point. Preferred for structural grids and overall building dimensions. Reduces cumulative error.

1. Chain Dimensions (continuous): Sequential dimensions from point to

point. Used for wall-to-wall dimensions, opening locations. Three dimension strings typical: overall, grid-to-grid, wall-to-wall.

1. Ordinate Dimensions: X-Y coordinates from a datum point. Used in

site plans and complex curved geometry.

General rules:

• Dimension to face of structure, not finish, unless specifically noting

finish dimensions

• Place dimensions outside the building footprint where possible
• Use three dimension strings: overall, intermediate (grid-to-grid), and

detailed (opening-to-opening)

• Dimension text should read from bottom or right side of sheet
• Use consistent units: mm for metric, feet-inches for imperial
• Avoid crossing dimension lines over each other

2.6 North Arrow and Scale Bar

• North arrow: Required on every plan drawing. Use project north (aligned

to building grid) with true north indicated by separate arrow if different.

• Scale bar: Graphic scale bar required on every drawing. Numeric scale

alone is insufficient because drawings may be reproduced at different sizes. Graphic bar maintains accuracy regardless of print scaling.

• Scale bar length: Typically represents a round number (1m, 5m, 10m).

3. BIM Level of Development (LOD) Requirements

3.1 LOD Definitions

The BIM Forum LOD Specification defines the following levels:

LOD 100 -- Concept Design

• Overall building massing, volume, and area
• Generic placeholders indicating approximate size, shape, location
• Used for: conceptual analysis, early cost modeling, scheduling
• Geometric accuracy: Not reliable for measurement