mp-ai-20/mechanical-engineering-skills/acoustic-emission

Claude Code and agent skill by mp-ai-20/mechanical-engineering-skills

Trust tier 3
  • community
Source check pending

Checking that the SKILL.md file is still in the repository.

Acoustic emission (AE) testing — Kaiser effect, source location, AE parameters (count, energy, amplitude), wave modes, transducer selection, pressure vessel monitoring, ASME Section V Article 12, ASTM E1316.

Install

npx vskill@latest install mp-ai-20/mechanical-engineering-skills/acoustic-emission

SKILL.md

The same SKILL.md was published earlier as mp-ai-20/mechanical-engineering-skills/acoustic-emission.

Acoustic Emission Testing — Complete Skill

Physical Basis

Acoustic emission (AE): transient elastic waves generated by rapid stress relaxation within a material Sources: crack initiation/growth, plastic deformation, corrosion, phase transformation, fiber breakage (composites), delamination, leaks (fluid AE)

Wave propagation: body waves (P and S) + guided waves (Lamb) in plate structures Frequency range: 20 kHz – 1 MHz (most structural AE: 50–400 kHz) Velocity: V_P = √[E(1-ν) / (ρ(1+ν)(1-2ν))] [m/s; longitudinal wave] V_S = √[G/ρ] = V_P × √[(1-2ν)/(2(1-ν))] [m/s; shear wave] Steel: V_P ≈ 5960 m/s; V_S ≈ 3230 m/s

Key AE Parameters

Hit: single AE event exceeding threshold at one sensor

AE signal parameters:

  • Amplitude A: peak voltage of waveform [dBae; 0 dBae = 1 μV at transducer]

A [dBae] = 20 log₁₀(V_peak [μV])

  • Ring-down count: number of threshold crossings in one hit; indicative of signal duration
  • Duration: time from first to last threshold crossing [μs]
  • Rise time: time from first crossing to peak [μs]
  • Energy E: integral of squared voltage over duration [aJ or arbitrary units]

E = (1/R_load) ∫ V²(t) dt

  • Frequency: peak frequency or centroid frequency [kHz]

Threshold setting: Fixed threshold: 40–50 dBae typical (above noise floor by 6 dB) Floating threshold: adapts to background noise (EMI environments) Peak definition threshold (PDT): 20–50 μs after first crossing

Kaiser and Felicity Effects

Kaiser effect: no AE below previously applied maximum load Material is "quiet" when re-loaded below prior maximum stress → indicates material has not experienced additional damage

Felicity effect (reverse of Kaiser): AE occurs below prior maximum load Felicity Ratio: FR = P_AE_onset / P_previous_max [< 1 indicates damage] ASTM E569 accepts FR ≥ 0.95 for composite vessels; FR < 0.85 → significant damage

Significance: FR ≥ 1.0 → no new damage since last test (Kaiser effect holds) FR < 1.0 → progressive damage; source re-activates at lower load

Source Location

Linear Location (1D)

Two sensors A and B at distance d apart Δt = t_B - t_A [time difference of arrival] Source location x from midpoint: x = Δt × V / 2

Planar Location (2D)

Three or more sensors; solve: (x_source - x_i)² + (y_source - y_i)² = (V × t_i - d_ref)² Overdetermined system → least squares solution Accuracy: ±5–20 mm for well-calibrated systems

Time Difference of Arrival (TDOA)

TDOA_ij = t_i - t_j = (d_i - d_j) / V Hyperbolae intersection → source

Velocity calibration: Use pencil lead break (Hsu-Nielsen source) at known locations PLB: 2H mechanical pencil; 0.3 or 0.5 mm; standardized AE source

Transducer Types

Resonant transducers: high sensitivity at resonant frequency (most common)

  • Frequency range: 50–400 kHz (narrow band)
  • Typical resonance: 150 kHz or 300 kHz
  • Sensitivity: −65 to −55 dBV/μbar (resonant); referenced to manufacturer calibration

Wideband transducers: 50–1000 kHz flat response; for signal analysis and source characterization Less sensitive than resonant; used in research applications

Sensor coupling: thin layer of grease (Dow Corning 111); magnetic hold-down or band clamp Coupling check: pencil lead break test; amplitude > threshold + adequate waveform

Preamplifier: gain 40 or 60 dB; located at sensor; filters noise before long cable run System gain: 0 + 40 dB preamplifier + software gain

Test Configuration — Pressure Vessel

Sensor spacing: V_P × t_rise → maximum source-to-sensor distance for detection For steel vessel: V_P = 5960 m/s; t_rise ≈ 1 ms (detectability); max distance ≈ 6 m Practical: sensors every 3–5 m on large vessels

Pressurization protocol (ASME V Art. 12): Load in steps (25%, 50%, 75%, 90%, 100% design pressure) Hold at each step; monitor AE activity; proceed only if AE stable Rate: 5–10% of design pressure per minute

Accept/reject criteria (ASME PCC-3): Grade A: low activity, no location, no Felicity effect → acceptable Grade B: moderate activity, located sources → monitor, evaluate Grade C: high activity, Felicity effect FR < 0.85 → reject; inspect source by other NDE Grade D: continuous AE; test aborted → failed

Composite Pressure Vessels

CFRP vessel monitoring: AE sources: matrix cracking (50–150 kHz), delamination (100–250 kHz), fiber fracture (300–500 kHz) Burst precursor: amplitude increase + frequency shift toward higher frequency ASTM E1888 / EN 14585: AE test procedure for composite overwrapped pressure vessels

Discrimination: Matrix cracking: low amplitude (45–60 dBae), high count/energy ratio Fiber fracture: high amplitude (70–90 dBae), low count/energy Delamination: intermediate amplitude, long duration

Leak Detection with AE

Fluid leak through crack or orifice: Turbulent flow generates broad-band AE (10–500 kHz) P_AE ∝ Q_leak × ΔP [proportional to flow rate × pressure difference]

Leak location: time-of-arrival difference between two sensors Minimum detectable leak: 0.1–1.0 cc/min depending on vessel, pressure, sensor

Standards

StandardScope
ASME Section V Article 12AE examination of metallic pressure vessels
ASTM E1316AE terminology
ASTM E976Mounting and coupling transducers
ASTM E569AE monitoring during hydrostatic testing
ASTM E1888AE testing of composite pressure vessels
EN 1330-9AE terms and definitions

Output

Provide: sensor type and frequency [kHz], sensor spacing [m], threshold [dBae], preamplifier gain [dB], AE parameters to record (amplitude, energy, count, duration, frequency), source location method and expected accuracy [mm], pressurization protocol (steps [%], rate [%/min]), Kaiser/Felicity ratio check procedure, accept/reject criteria (Grade A–D per ASME PCC-3), and applicable standard (ASME Section V Article 12, ASTM E569).

Security

  • Security scanPassed, 90 of 100Pattern checks on the skill's files.
  • Model reviewPassed

Quality evaluation

  • Task evaluationNot runNo evaluation yet. Run one in Skill Studio.

Source

Popularity

7-day trend score
0

Not refreshed yet.

Works with

Any agent vskill installs to: 56 targets in all. These 39 have a page on this site.

  • Claude Code
  • Cursor
  • GitHub Copilot
  • Windsurf
  • Codex
  • Gemini CLI
  • Cline
  • Amp
  • Roo Code
  • Goose
  • Continue
  • Kilo Code
  • Junie
  • Trae
  • OpenHands
  • Qwen Code
  • AI Agent
  • Tabnine Chat
  • Sourcegraph Cody
  • Amazon Q
  • Firebase Genkit
  • Sweep
  • Devin
  • Phind
  • Mentat
  • Claude Desktop
  • Aider
  • GPT Pilot
  • Plandex
  • bolt.new
  • v0
  • Replit Agent
  • Anse
  • TypingMind
  • BetterChatGPT
  • LibreChat
  • Warp AI
  • Pieces
  • Fig AI
Embed badge
vskill VERIFIED badge
[![vskill VERIFIED](https://verified-skill.com/api/v1/skills/mp-ai-20/mechanical-engineering-skills/acoustic-emission/badge)](https://verified-skill.com/skills/mp-ai-20/mechanical-engineering-skills/acoustic-emission)

Something wrong with this skill or its page? Tell us.