mp-ai-20/mechanical-engineering-skills/adhesive-joints

Claude Code and agent skill by mp-ai-20/mechanical-engineering-skills

Trust tier 3
  • community
Source check pending

Checking that the SKILL.md file is still in the repository.

Adhesive joint design — lap joint stress (Volkersen, Goland-Reissner), peel stress, failure modes, surface preparation, structural adhesives, design guidelines.

Install

npx vskill@latest install mp-ai-20/mechanical-engineering-skills/adhesive-joints

SKILL.md

The same SKILL.md was published earlier as mp-ai-20/mechanical-engineering-skills/adhesive-joints.

Adhesive Joint Design — Complete Skill

Joint Types

  • Single-lap: simple; peel and bending stresses at overlap ends
  • Double-lap: balanced; reduces peel; still has shear non-uniformity
  • Scarf joint: low peel; best stress uniformity; requires precision machining
  • Butt joint: poor shear/peel; avoid for structural loads
  • Stepped-lap: most efficient; used in composite repair (F/A-18, B-2)

Volkersen Shear Stress Distribution (Elastic)

For single-lap joint, adhesive shear stress:

τ(x) = T/(2bt) × ω × cosh(ωx/2) / sinh(ωL/2) + T/(2bt) × [non-uniform terms]

Simplified (uniform substrates, symmetric): τ_max/τ_avg = ω L/2 × coth(ω L/2)

where ω = √(2G_a / (t_a × E_s × t_s)) G_a = adhesive shear modulus; t_a = adhesive thickness; E_s t_s = substrate stiffness

Adhesive shear stress concentration: highest at ends of overlap

Goland-Reissner (Includes Bending)

Single-lap joint with eccentric load path → bending moment at overlap ends Peel stress σ_y (tension or compression) superimposed on shear Peak occurs at free ends of overlap

Bending moment factor: k = [1 + 2√2 tanh(...)]/... (see Goland-Reissner 1944) Peak peel stress often governs failure — adhesives weak in tension

Design Rules for Lap Joints

  1. Keep peel stress low: extend overlap length; use tapered (spew) fillet at ends
  2. Overlap length: L ≥ 25–30 mm minimum; typically L/t_s ≥ 50 for structural
  3. Increasing overlap beyond effective length: no strength gain (peak shear unchanged)
  4. Adhesive thickness: t_a = 0.1–0.3 mm optimal; thin = brittle, thick = low strength
  5. Scarf angle: 5°–10° for structural — distributes shear+peel uniformly
  6. Avoid tension-butt loading — use fillets, doublers, or step joints instead

Failure Modes

ModeCausePrevention
Cohesive failureAdhesive bulk yields/fracturesUse tougher adhesive
Adhesive failureBond line separates from substrateBetter surface prep
Substrate failureAdherend tearsIncrease substrate thickness
Peel failureEnd stress concentrationTaper, longer overlap
Environmental degradationMoisture uptakeSealant, compatible primer

Structural Adhesive Types

TypeShear StrengthT-peelTemperatureNotes
Epoxy (2-part)15–40 MPaLow-Med–55 to 120°CMost common structural
Epoxy-film (structural)30–50 MPaHigh–55 to 150°CAerospace (Cytec, Hexcel)
Acrylic (structural)15–30 MPaHigh–55 to 120°CFast cure; works on oily surfaces
Polyurethane5–15 MPaVery high–50 to 90°CFlexible; crash-resistant
Cyanoacrylate10–25 MPaVery low–50 to 80°CBrittle; small area only
Silicone0.5–5 MPaModerate–65 to 250°CSealant; low structural

Surface Preparation (Critical)

Adhesive failure most common cause: inadequate surface prep Steel: blast to Sa 2.5 (SIS 05 59 00), apply primer within 4 hours Aluminum: etching (FPL or P2 etch), phosphoric anodize, or grit blast + silane CFRP: light abrade + solvent wipe; avoid deep scratching of fibers Ti: CAA (chromic acid anodize) or PASA-JELL + primer Contact angle: ≤ 10° water contact = excellent; ≥ 30° = poor prep

Environmental Effects

Moisture reduces strength 20–50% for epoxy adhesives (long-term immersion) Design knock-down factor: use 50% of dry strength for wet/hot environment Primer selection critical for hot-wet durability (BR-127, BR-6747-1 aerospace)

Fracture Mechanics Approach

Mode I fracture toughness G_IC of bond line governs peel failure Typical G_IC: brittle epoxy 0.3–0.8 kJ/m²; toughened epoxy 1–3 kJ/m²; structural film 2–4 kJ/m² DCB (double cantilever beam) test: G_IC = 12F²a²/(E b² h³)

Output

Provide: joint type, overlap length L [mm], τ_max [MPa] vs. shear strength, peel stress σ_peel [MPa] vs. allowable, adhesive selection, surface preparation specification, environmental knock-down applied, failure mode predicted.

Security

  • Security scanPassed, 90 of 100Pattern checks on the skill's files.
  • Model reviewPassed

Quality evaluation

  • Task evaluationNot runNo evaluation yet. Run one in Skill Studio.

Source

Popularity

7-day trend score
0

Not refreshed yet.

Works with

Any agent vskill installs to: 56 targets in all. These 39 have a page on this site.

  • Claude Code
  • Cursor
  • GitHub Copilot
  • Windsurf
  • Codex
  • Gemini CLI
  • Cline
  • Amp
  • Roo Code
  • Goose
  • Continue
  • Kilo Code
  • Junie
  • Trae
  • OpenHands
  • Qwen Code
  • AI Agent
  • Tabnine Chat
  • Sourcegraph Cody
  • Amazon Q
  • Firebase Genkit
  • Sweep
  • Devin
  • Phind
  • Mentat
  • Claude Desktop
  • Aider
  • GPT Pilot
  • Plandex
  • bolt.new
  • v0
  • Replit Agent
  • Anse
  • TypingMind
  • BetterChatGPT
  • LibreChat
  • Warp AI
  • Pieces
  • Fig AI
Embed badge
vskill VERIFIED badge
[![vskill VERIFIED](https://verified-skill.com/api/v1/skills/mp-ai-20/mechanical-engineering-skills/adhesive-joints/badge)](https://verified-skill.com/skills/mp-ai-20/mechanical-engineering-skills/adhesive-joints)

Something wrong with this skill or its page? Tell us.