mp-ai-20/mechanical-engineering-skills/air-bearing

Claude Code and agent skill by mp-ai-20/mechanical-engineering-skills

Trust tier 2
  • community
LLM review pending
Source check pending

Checking that the SKILL.md file is still in the repository.

Air bearings — hydrostatic vs. aerodynamic, load capacity, stiffness, orifice/porous compensation, squeeze film, precision spindles, cleanroom applications, ISO 12849 design.

Install

npx vskill@latest install mp-ai-20/mechanical-engineering-skills/air-bearing

SKILL.md

The same SKILL.md was published earlier as mp-ai-20/mechanical-engineering-skills/air-bearing.

Air Bearings — Complete Skill

Types of Air Bearings

Hydrostatic (aerostatic): pressurized external air supply; load capacity independent of speed; zero contact at startup/shutdown Aerodynamic: self-generating pressure from rotor rotation; requires minimum speed; no external supply

Hydrostatic Air Bearing Fundamentals

Governing Equation (Compressible Reynolds)

Thin film compressible lubrication: ∂/∂x[(Ph³ ∂P/∂x)/η] + ∂/∂z[(Ph³ ∂P/∂z)/η] = 12 ∂(Ph)/∂t + 6 U ∂(Ph)/∂x

P = absolute pressure; h = gap; η = air viscosity (1.85×10⁻⁵ Pa·s at 20°C); U = surface speed

Compressibility number: σ = 6 η ω L² / (P_a h₀²) [ω = angular speed; L = bearing half-length; P_a = supply pressure; h₀ = nominal gap] For σ < 1: quasi-static; for σ >> 1: compressibility important

Orifice-Compensated Bearing

Flow through orifice (supply to pocket): Q_s = C_d × A_o × √(2(P_s - P_p)/ρ) [m³/s; incompressible; valid for P_s - P_p small] A_o = π d_o²/4 [m²]; d_o = orifice diameter; C_d = 0.6–0.8 (discharge coefficient)

Pocket pressure P_p (equating supply flow to bearing flow): Q_s = Q_bearing = [P_p³ - P_a³] × C_bearing / (P_p) [compressible film flow; C_bearing = geometric constant]

Load capacity (circular pad): W = ∫∫(P - P_a)dA ≈ (P_p - P_a) × A_eff [effective area A_eff ≈ 0.6–0.8 × pad area for typical geometry]

Stiffness (orifice-compensated): k = -dW/dh|_{h=h₀} [N/m; should be positive for stability] Optimal stiffness at: Q_s orifice = Q_bearing [matched at operating point]

Maximum stiffness condition: P_p = √(P_s × P_a) [optimal pocket pressure; P_s = supply; P_a = atmospheric]

Porous-Media Compensated Bearing

Flow through porous pad: Q_porous = (k_p × A / L_p) × (P_s - P_p) [Darcy's law; k_p = permeability [m²]; L_p = thickness [m]] Typical graphite: k_p = 10⁻¹³ to 10⁻¹² m²

Advantages: no orifice clogging; more uniform pressure distribution; better damping Disadvantages: requires clean, dry air (moisture blocks pores)

Aerodynamic Bearings

Spiral Groove Thrust Bearing

Pressure generation from pumping grooves: At rotation speed ω: grooves pump gas inward (or outward) → pressure buildup in land region P_peak = f(σ, groove geometry) → solved numerically

Load capacity: W = (P_peak - P_a) × A_land [approximate; full solution requires Reynolds equation solution]

Stiffness: k_aero ∝ ω × h₀⁻² [stiffness increases with speed and decreases with gap] Minimum speed for load support: ω_min = √(W × k_B / (k_aero_factor × R²))

Journal Aerodynamic Bearing (Foil Bearing)

Foil bearing (compliant): corrugated metallic foils provide structural compliance + damping Load at speed: depends on Sommerfeld number and speed At 50,000 RPM: typical foil bearing capacity 50–500 N Applications: aircraft APU, micro gas turbines, oil-free compressors

Practical Design Parameters

Nominal gap h₀: Typical: 5–20 μm (precision); 10–50 μm (industrial) Smaller gap: higher stiffness, higher load capacity, higher flow rate, more sensitive to contamination

Supply pressure P_s: Typical: 3–8 bar (gauge) Higher P_s → higher load capacity but more flow (air consumption)

Air consumption: Q_air = N_pads × Q_per_pad [slm or L/min; must size filter/dryer + supply] Typical: 10–200 slm for small bearing systems

Cleanliness requirement: Particle size < 1/10 gap (< 1–2 μm for 10 μm gap) ISO 8573-1: particle class 1; moisture < -40°C pressure dew point

Load Capacity — Flat Pad (Hydrostatic)

Circular pad with annular orifice ring: W_max ≈ (P_s - P_a) × A_pad × η_p [η_p = pressure factor ≈ 0.4–0.6 depending on geometry]

Design example: D = 50 mm pad; P_s = 5 bar gauge; P_a = 1 bar abs → ΔP = 5 bar A_pad = π(0.025)² = 1.96×10⁻³ m² W ≈ 5×10⁵ × 1.96×10⁻³ × 0.5 ≈ 490 N per pad

Error Motion and Accuracy

Averaging effect (preloaded air bearing): Position accuracy = h₀ × (δP / P_mean) × (1 / k_normalized) Practical: air bearing achieves 5–20 nm positioning accuracy (surface finish averaging)

Thermal effects: Linear CTE of steel: 11.7 μm/(m·°C); 1°C change in 300 mm span → 3.5 μm gap change Use Invar (1.5 μm/(m·°C)) or temperature control for sub-micron applications

Applications

ApplicationTypeh₀ [μm]Load [N]
CMM slidesHydrostatic5–10200–5000
Precision spindleHydrostatic10–2050–2000
Silicon wafer stageHydrostatic5–850–500
Turbine (oil-free)Foil aero20–50100–2000
GyroscopeHydrostatic2–51–10

Output

Provide: bearing type (hydrostatic orifice/porous/aerodynamic foil), nominal gap h₀ [μm], supply pressure P_s [bar], pad area and geometry, load capacity W [N] per pad, static stiffness k [N/μm], air consumption [slm], minimum speed for aerodynamic (if applicable), cleanliness class (ISO 8573-1), error motion [nm], temperature sensitivity [μm/°C], and design reference (ISO 12849, bearing manufacturer specs).

Security

  • Security scanPassed, 100 of 100Pattern checks on the skill's files.
  • Model reviewNot runA model review is scheduled for the next rescan.

Quality evaluation

  • Task evaluationNot runNo evaluation yet. Run one in Skill Studio.

Source

Popularity

7-day trend score
0

Not refreshed yet.

Works with

Any agent vskill installs to: 56 targets in all. These 39 have a page on this site.

  • Claude Code
  • Cursor
  • GitHub Copilot
  • Windsurf
  • Codex
  • Gemini CLI
  • Cline
  • Amp
  • Roo Code
  • Goose
  • Continue
  • Kilo Code
  • Junie
  • Trae
  • OpenHands
  • Qwen Code
  • AI Agent
  • Tabnine Chat
  • Sourcegraph Cody
  • Amazon Q
  • Firebase Genkit
  • Sweep
  • Devin
  • Phind
  • Mentat
  • Claude Desktop
  • Aider
  • GPT Pilot
  • Plandex
  • bolt.new
  • v0
  • Replit Agent
  • Anse
  • TypingMind
  • BetterChatGPT
  • LibreChat
  • Warp AI
  • Pieces
  • Fig AI
Embed badge
vskill VERIFIED badge
[![vskill VERIFIED](https://verified-skill.com/api/v1/skills/mp-ai-20/mechanical-engineering-skills/air-bearing/badge)](https://verified-skill.com/skills/mp-ai-20/mechanical-engineering-skills/air-bearing)

Something wrong with this skill or its page? Tell us.