mp-ai-20/mechanical-engineering-skills/aluminum-alloys
Claude Code and agent skill by mp-ai-20/mechanical-engineering-skills
- community
Checking that the SKILL.md file is still in the repository.
Aluminum alloy designation, tempers, properties table (2xxx, 5xxx, 6xxx, 7xxx), weldability, formability, corrosion resistance, selection guide, casting alloys.
Install
npx vskill@latest install mp-ai-20/mechanical-engineering-skills/aluminum-alloysSKILL.md
The same SKILL.md was published earlier as mp-ai-20/mechanical-engineering-skills/aluminum-alloys.
Aluminum Alloys — Complete Skill
Designation System (AA/ANSI)
4-digit wrought: XXXX 1st digit = major alloying element: 1=pure Al, 2=Cu, 3=Mn, 4=Si, 5=Mg, 6=Mg+Si, 7=Zn, 8=other 2nd digit: modification (0=original, 1-9=modification) 3rd+4th: minimum Al % or arbitrary designation
Temper designations (after dash): -F: as fabricated; -O: annealed; -H: strain hardened; -T: thermally treated -T4: solution heat treated + naturally aged -T6: solution + artificially aged (peak strength) -T73: solution + over-aged (improved SCC resistance, -10% strength vs T6) -T76: solution + over-aged (intermediate) -T851: T8 + stress relieved (stretched)
Properties by Series
2xxx Series (Al-Cu, high strength)
2024-T3: S_y = 345 MPa, S_u = 483 MPa, El = 18%, E = 73 GPa — aerospace structure 2024-T4: S_y = 324 MPa, S_u = 469 MPa, El = 20% 2014-T6: S_y = 414 MPa, S_u = 483 MPa — structural applications, forgings Weldability: poor (hot cracking); use adhesive or rivets Corrosion: susceptible; requires cladding (Alclad) or anodizing
5xxx Series (Al-Mg, moderate strength, non-heat-treatable)
5052-H32: S_y = 193 MPa, S_u = 228 MPa — sheet, marine, fuel tanks 5083-H116: S_y = 228 MPa, S_u = 317 MPa — marine, cryogenic, weldable structures 5086-H112: S_y = 152 MPa, S_u = 262 MPa Excellent weldability (match with 5356 filler); good corrosion resistance; not age-hardenable
6xxx Series (Al-Mg-Si, medium strength, excellent all-rounder)
6061-T6: S_y = 276 MPa, S_u = 310 MPa, El = 12% — structural, extrusions, machined parts 6063-T5: S_y = 145 MPa, S_u = 186 MPa — architectural extrusions 6082-T6: S_y = 260 MPa, S_u = 310 MPa (European equivalent to 6061) Good weldability (4043 or 5356 filler), good formability, excellent extrude-ability Corrosion: good; anodizes well; slight HAZ softening after welding
7xxx Series (Al-Zn, highest strength)
7075-T6: S_y = 503 MPa, S_u = 572 MPa, El = 11% — highest strength wrought Al 7075-T73: S_y = 435 MPa, S_u = 503 MPa — SCC resistant version 7050-T7451: S_y = 455 MPa, S_u = 510 MPa — aerospace thick plates 7150-T7751: S_y = 490 MPa, S_u = 525 MPa — upper wing stringers Weldability: poor; typically riveted or bonded Corrosion: susceptible (use -T73/-T76 for SCC); use Alclad or anodize
Casting Alloys (3-digit + decimal)
A356.0-T6: S_y = 207 MPa, S_u = 262 MPa, El = 6% — most common casting alloy (wheels, engine) 319.0-T6: S_y = 165 MPa, S_u = 250 MPa — engine blocks, cylinder heads 380.0 (die cast): S_y = 165 MPa, S_u = 317 MPa — general die castings
Corrosion Behavior
Naturally forms protective Al₂O₃ film: self-passivating in air Susceptible environments: saltwater (pitting), alkaline solutions Galvanic: Al is anodic vs. most metals; acceptable vs. stainless (same coating condition) Anodizing: thickens oxide (5-25 μm type II; 25-100 μm hardcoat type III)
Selection Guide
| Application | Alloy | Reason | |
|---|---|---|---|
| Aerospace wing skins | 2024-T3 | Fatigue; damage tolerance | |
| Aerospace wing spars | 7075-T6 or 7150 | Highest strength | |
| Extrusions (structural) | 6061-T6 | Extrudable, weldable, structural | |
| Marine (welded) | 5083-H116 | Weldable, corrosion resistant | |
| Machined precision parts | 6061-T6 or 7075-T6 | Machinability + strength | |
| Automotive castings | A356-T6 | Castability + strength | |
| Architectural | 6063-T5 | Surface quality, anodizing |
Weldability Guide
5xxx → 5xxx: use 5356 filler (ER5356) 6061 → 6061: use 4043 filler (lower crack susceptibility) or 5356 (higher strength joint) 2xxx and 7xxx: generally non-weldable by fusion; use FSW or mechanical fastening Joint efficiency: 6061-T6 weld → joint = ~55% of parent (HAZ softens to T4 equivalent)
Output
Provide: alloy and temper recommendation, S_y and S_u [MPa], density [kg/m³], weld filler if applicable, corrosion protection recommendation, applicable heat treatment, fatigue endurance limit [MPa].
Security
- Security scanPassed, 90 of 100Pattern checks on the skill's files.
- Model reviewPassed
Quality evaluation
- Task evaluationNot runNo evaluation yet. Run one in Skill Studio.
Source
- SKILL.md in the repositoryCheckingskills/aluminum-alloys/SKILL.md
Popularity
- 7-day trend score
- 0
Not refreshed yet.
Works with
Any agent vskill installs to: 56 targets in all. These 39 have a page on this site.
- Claude Code
- Cursor
- GitHub Copilot
- Windsurf
- Codex
- Gemini CLI
- Cline
- Amp
- Roo Code
- Goose
- Continue
- Kilo Code
- Junie
- Trae
- OpenHands
- Qwen Code
- AI Agent
- Tabnine Chat
- Sourcegraph Cody
- Amazon Q
- Firebase Genkit
- Sweep
- Devin
- Phind
- Mentat
- Claude Desktop
- Aider
- GPT Pilot
- Plandex
- bolt.new
- v0
- Replit Agent
- Anse
- TypingMind
- BetterChatGPT
- LibreChat
- Warp AI
- Pieces
- Fig AI
Embed badge
[](https://verified-skill.com/skills/mp-ai-20/mechanical-engineering-skills/aluminum-alloys)