mp-ai-20/mechanical-engineering-skills/am-build-orientation

Claude Code and agent skill by mp-ai-20/mechanical-engineering-skills

Trust tier 3
  • community
  • ext:[{"type":"hook","description":"Pre/post lifecycle hooks"}]
Source check pending

Checking that the SKILL.md file is still in the repository.

AM build orientation — anisotropy effects, surface finish vs. orientation, support minimization, staircase effect, thermal gradient, LPBF/FDM/SLA orientation strategies, build time estimation.

Install

npx vskill@latest install mp-ai-20/mechanical-engineering-skills/am-build-orientation

Semi-extensibleMentions customization, but needs skill-specific knowledge. Read the extensible skills standard

SKILL.md

The same SKILL.md was published earlier as mp-ai-20/mechanical-engineering-skills/am-build-orientation.

AM Build Orientation — Complete Skill

Orientation Effects on Part Quality

Mechanical Properties (Anisotropy)

LPBF metals (e.g., Ti-6Al-4V): Z-direction (build): lowest ductility due to columnar grain structure and layer interfaces XY-plane (horizontal): higher ductility and fatigue resistance Typical ratio: σ_UTS(Z) / σ_UTS(XY) = 0.90–0.97 (small difference in tensile) Fatigue: Z-direction life typically 50–80% of XY life at same stress

FDM (polymer): Z-direction: weakest; bonds between layers (inter-layer adhesion strength) Strength ratio σ_Z / σ_XY ≈ 0.4–0.7 for ABS/PLA Design rule: orient critical load paths in XY plane (parallel to layers)

Critical orientation rule: Determine primary load direction → align principal stress direction parallel to build plane (XY) wherever possible

Surface Finish (Staircase Effect)

Theoretical Ra for inclined surface: Ra = (t_layer)² × sin(θ) × cos(θ) / (4 × sin²(θ)) ≈ t_layer × tan(θ) / 4 [for small θ] θ = angle from horizontal; t_layer = layer thickness [μm]

Staircase effect: At θ = 45°: Ra ≈ t_layer / 4 At θ = 90° (vertical): Ra → t_layer / 2 (scallop = half-layer) Upskin (facing up): better Ra (remelted by next pass); Ra ≈ 5–15 μm for LPBF at 30 μm layers Downskin (facing down, unsupported): rougher; Ra ≈ 15–40 μm; requires support or 45° limit

Rule: functional surfaces should be upward-facing or vertical in build direction

Critical Angle for Support-Free

LPBF (metal): Self-supporting if angle from horizontal > 45° (material- and parameter-dependent) Below 45°: overhangs require support structure AlSi10Mg: often needs support below 35°; Ti-6Al-4V: 40°; SS316L: 45°

FDM (polymer): Self-supporting for angles > 45° from horizontal (varies by material and cooling) Standard rule: support required for angles < 45° overhang from vertical = > 45° from horizontal

SLA/DLP: All overhangs in XY need support; only gravity matters (support below overhangs)

Orientation Optimization Objectives

Multi-objective optimization:

  1. Minimize support volume (cost + post-processing)
  2. Maximize surface finish quality on critical surfaces
  3. Minimize anisotropy effect on critical load direction
  4. Minimize build height (reduce build time)
  5. Thermal gradient management (residual stress)

Mathematical formulation: Minimize: w₁ × V_support + w₂ × A_roughsurface + w₃ × h_build Subject to: load-aligned mechanical property constraint

Pareto front: trade-off between support volume and build height; select based on priorities

Thermal Gradient and Residual Stress

LPBF residual stress pattern: Tensile near top surface; compressive in bulk Largest distortion: thin flat parts built horizontal (parallel to build plate) Better: orient thin parts vertically (reduce bending moment from thermal gradient)

Distortion tendency: Parts with large base area → high compressive residual stress → curling/warping Reduce by: building upright; scanning island strategy; annealing post-build

Scan strategy interaction: Chessboard (island) scanning: reduces residual stress vs. long stripe scan 67° rotation of scan angle between layers: improves isotropic mechanical properties

Support Structure Strategy

Support types: Block support: solid block; easiest to remove; waste material; use for large overhangs Line/lattice support: reduces material; lighter; harder to remove Conical support (LPBF): tapered for easy removal with wire cutter Tree support (FDM/SLA): minimal contact → easier removal; optimized for polymer

Support contact: LPBF: support touching surface leaves marks (Ra 20–50 μm); use conical touch points Post-process: EDM, milling, or polishing support contact areas

Support volume formula: V_support = A_projected_overhangs × t_layer × n_layers_of_support Roughly: V_support ≈ 5–30% of part volume (worst case, horizontal part)

Build Time Estimation

LPBF build time: t_build = h_build / (t_layer × layer_rate) + t_recoat × n_layers t_layer = layer thickness [mm]; layer_rate = build rate [mm/s] varies by area/strategy h_build = total build height [mm]

FDM build time: t_build ≈ V_part × ρ_infill / (e_width × e_height × V_head) + overhead V_head = extrusion rate [mm³/s]; infill density [%] controls time

Machine time comparison (LPBF, one part): Horizontal orientation: h_build = 30 mm → t ≈ 3 hr Vertical orientation: h_build = 100 mm → t ≈ 10 hr Trade-off: vertical = better surface on critical faces + more support = longer build

Practical Decision Guidelines

PriorityRecommended orientation
Best XY mechanical propertiesOrient load path in XY plane
Minimum supportsOrient largest flat face down
Best surface on specific faceOrient that face upward (upskin)
Minimum build timeOrient shortest dimension vertical
Minimum residual stressOrient to minimize base plate adhesion

Output

Provide: recommended build orientation (angle from build plate for each principal face), critical surface identification (upskin/downskin/vertical), estimated Ra [μm] on each functional surface, support volume [cm³] and fraction of part volume [%], build height [mm], estimated build time [hr], anisotropy effect on critical load path (XY vs. Z strength ratio), residual stress/distortion risk (low/medium/high), post-processing requirements at support attachment zones, and staircase height [μm] at critical angles.

Security

  • Security scanPassed, 90 of 100Pattern checks on the skill's files.
  • Model reviewPassed

Quality evaluation

  • Task evaluationNot runNo evaluation yet. Run one in Skill Studio.

Source

Popularity

7-day trend score
0

Not refreshed yet.

Extension points

  • hookPre/post lifecycle hooks

Works with

Any agent vskill installs to: 56 targets in all. These 39 have a page on this site.

  • Claude Code
  • Cursor
  • GitHub Copilot
  • Windsurf
  • Codex
  • Gemini CLI
  • Cline
  • Amp
  • Roo Code
  • Goose
  • Continue
  • Kilo Code
  • Junie
  • Trae
  • OpenHands
  • Qwen Code
  • AI Agent
  • Tabnine Chat
  • Sourcegraph Cody
  • Amazon Q
  • Firebase Genkit
  • Sweep
  • Devin
  • Phind
  • Mentat
  • Claude Desktop
  • Aider
  • GPT Pilot
  • Plandex
  • bolt.new
  • v0
  • Replit Agent
  • Anse
  • TypingMind
  • BetterChatGPT
  • LibreChat
  • Warp AI
  • Pieces
  • Fig AI
Embed badge
vskill VERIFIED badge
[![vskill VERIFIED](https://verified-skill.com/api/v1/skills/mp-ai-20/mechanical-engineering-skills/am-build-orientation/badge)](https://verified-skill.com/skills/mp-ai-20/mechanical-engineering-skills/am-build-orientation)

Something wrong with this skill or its page? Tell us.