mp-ai-20/mechanical-engineering-skills/balancing-in-situ
Claude Code and agent skill by mp-ai-20/mechanical-engineering-skills
- community
Checking that the SKILL.md file is still in the repository.
In-situ (field) balancing — influence coefficient method, trial weight, single-plane/two-plane, vibration measurement, ISO 1940 balance quality grades, residual unbalance acceptance.
Install
npx vskill@latest install mp-ai-20/mechanical-engineering-skills/balancing-in-situSKILL.md
The same SKILL.md was published earlier as mp-ai-20/mechanical-engineering-skills/balancing-in-situ.
In-Situ Rotor Balancing — Complete Skill
Unbalance Fundamentals
Static unbalance: mass off-center; vibration at 1× running speed (synchronous); force in one plane Couple unbalance: equal and opposite masses in two planes; no net force but creates moment Dynamic unbalance: combination; requires two-plane correction for complete balance
Unbalance force: F_u = m_u × e × ω² [N; m_u = unbalance mass [kg]; e = eccentricity [m]; ω = angular speed [rad/s]] Or: F_u = U × ω² [N; U = unbalance = m_u × e [kg·m]]
ISO 1940 residual unbalance (specific unbalance e_per): e_per = G × 1000 / ω [g·mm/kg; G = balance grade; ω in rad/s] U_per = e_per × M_rotor / 1000 [g·mm; M_rotor in kg]
Balance grades (ISO 1940-1):
| Grade | e_per × ω [mm/s] | Application | |
|---|---|---|---|
| G 0.4 | 0.4 | Precision gyroscopes | |
| G 1 | 1 | Machine tools, gas turbine rotors | |
| G 2.5 | 2.5 | Marine turbines, pumps | |
| G 6.3 | 6.3 | Process plant fans, pumps | |
| G 16 | 16 | Agricultural tractors | |
| G 40 | 40 | Crankshafts, single cylinders |
Example: G 6.3 fan, 1500 RPM (ω = 157 rad/s), mass 50 kg e_per = 6.3 × 1000 / 157 = 40 μm U_per = 40 × 50 / 1000 = 2 g·mm residual per plane
Single-Plane Balancing (Static)
Method:
- Measure initial vibration: A₀ = amplitude [mm/s or mils]; φ₀ = phase [°] (relative to 1× trigger)
- Add trial weight T at known angle θ_T
- Measure new vibration A_T; φ_T
- Calculate influence coefficient α:
α = (A_T e^{jφ_T} - A₀ e^{jφ₀}) / T [complex; mm/s per g·mm]
- Correction mass and angle:
T_corr = -A₀ e^{jφ₀} / α [complex weight; magnitude = mass; angle = placement angle]
Vector diagram (graphical method): Draw A₀ vector; draw trial-run result A_T; difference = effect of trial weight W Required correction = A₀ vector × (W / |W_effect|) in opposite direction
Two-Plane Balancing (Dynamic)
Influence coefficient matrix: [A₁] = [α₁₁ α₁₂] [U₁] [A₂] [α₂₁ α₂₂] [U₂]
A₁, A₂ = vibration at planes 1 and 2 (complex vectors) U₁, U₂ = unbalance corrections at planes 1 and 2 (complex) α_ij = influence coefficient: vibration at i due to unit unbalance at j
Measurement procedure:
- Original run: [A₁₀, A₂₀]
- Add trial T₁ at plane 1: measure [A₁₁, A₂₁]
- Remove T₁; add trial T₂ at plane 2: measure [A₁₂, A₂₂]
Influence coefficients: α₁₁ = (A₁₁ - A₁₀) / T₁; α₂₁ = (A₂₁ - A₂₀) / T₁ α₁₂ = (A₁₂ - A₁₀) / T₂; α₂₂ = (A₂₂ - A₂₀) / T₂
Solution for corrections: [U₁] [α₁₁ α₁₂]⁻¹ [-A₁₀] [U₂] = [α₂₁ α₂₂] × [-A₂₀]
Instrumentation
Vibration transducer: Proximity probe: measures shaft displacement [mil p-p or μm p-p]; required for fluid-film bearings (API 670) Accelerometer: measures housing vibration [m/s²]; useful for rolling element bearings
Phase reference: Keyphasor: optical or magnetic pickup on shaft; triggers once per revolution Phase angle: degrees from keyphasor to vibration peak (measured counter to rotation)
Analyzer: Single-channel: basic; measure 1× amplitude and phase with phase ref Multi-channel: simultaneous two-plane measurement; faster
Trial Weight Calculation
Trial weight guideline: T_trial = U_per / 5 to U_per / 10 [to get measurable change without overloading bearing] Or: T_trial [g] ≈ 6350 × rated_kW / (N_RPM²) × (D_correction / D_shaft) [for turbines] Place at known radius r_T; create U_T = T_trial × r_T [g·mm]
Placement accuracy: ±5° angular error acceptable; ±5 mm radial position error acceptable for most applications
Acceptance Criteria
ISO 10816-3 (vibration severity): Zone A (< 2.3 mm/s): new machine; acceptable Zone B (2.3–4.5 mm/s): acceptable for continued operation Zone C (4.5–7.1 mm/s): restricted operation; alarm condition Zone D (> 7.1 mm/s): danger; shutdown required
Residual unbalance verification (ISO 1940-2): After balancing: measure 1× vibration amplitude; check against allowable Or: spin rotor with calibrated unbalance; verify response within tolerance
API 670 (machinery protection systems): Alert: 1× amplitude > 0.4 × (12,000/N)^0.5 mils pp [typical; site-specific] Trip: 2× alert level
Balancing Below Critical Speed vs. At Speed
Rigid rotor (N < 0.7 N_critical): Two-plane static + dynamic balance sufficient; balance at low speed Modal shapes not relevant
Flexible rotor (N > N_critical): Modal balancing or influence coefficient at multiple speeds required Balance at running speed using in-situ influence coefficient method May need 3+ planes for multi-mode rotors
Standards
| Standard | Scope | |
|---|---|---|
| ISO 1940-1 | Balance quality grades for rigid rotors | |
| ISO 1940-2 | Verifying residual unbalance | |
| ISO 21940 | Vocabulary and rotor balancing procedures | |
| ISO 11342 | Flexible rotor balancing methods | |
| API 670 | Machinery protection systems (vibration limits) | |
| ISO 10816 | Mechanical vibration — evaluation criteria |
Output
Provide: balance grade (ISO 1940 G-number), allowable residual unbalance U_per [g·mm] per plane, single or two-plane procedure, trial weight mass [g] and radius [mm], measured amplitude and phase before/after correction [mm/s and °], influence coefficients α_ij (complex), correction mass and angle at each plane, post-balance vibration [mm/s vs. ISO 10816 zone], and applicable standard (ISO 1940, ISO 21940, API 670).
Security
- Security scanPassed, 90 of 100Pattern checks on the skill's files.
- Model reviewPassed
Quality evaluation
- Task evaluationNot runNo evaluation yet. Run one in Skill Studio.
Source
- SKILL.md in the repositoryCheckingskills/balancing-in-situ/SKILL.md
Popularity
- 7-day trend score
- 0
Not refreshed yet.
Works with
Any agent vskill installs to: 56 targets in all. These 39 have a page on this site.
- Claude Code
- Cursor
- GitHub Copilot
- Windsurf
- Codex
- Gemini CLI
- Cline
- Amp
- Roo Code
- Goose
- Continue
- Kilo Code
- Junie
- Trae
- OpenHands
- Qwen Code
- AI Agent
- Tabnine Chat
- Sourcegraph Cody
- Amazon Q
- Firebase Genkit
- Sweep
- Devin
- Phind
- Mentat
- Claude Desktop
- Aider
- GPT Pilot
- Plandex
- bolt.new
- v0
- Replit Agent
- Anse
- TypingMind
- BetterChatGPT
- LibreChat
- Warp AI
- Pieces
- Fig AI
Embed badge
[](https://verified-skill.com/skills/mp-ai-20/mechanical-engineering-skills/balancing-in-situ)