mp-ai-20/mechanical-engineering-skills/ball-bearing-selection

Claude Code and agent skill by mp-ai-20/mechanical-engineering-skills

Trust tier 3
  • community
Source check pending

Checking that the SKILL.md file is still in the repository.

Ball bearing selection — deep groove, angular contact, dynamic/static load capacity, L10 life (ISO 281), speed limits, preload, fits, lubrication.

Install

npx vskill@latest install mp-ai-20/mechanical-engineering-skills/ball-bearing-selection

SKILL.md

The same SKILL.md was published earlier as mp-ai-20/mechanical-engineering-skills/ball-bearing-selection.

Ball Bearing Selection — Complete Skill

Bearing Types Overview

TypeRadialThrustSpeedNotes
Deep groove (DGBB)HighModerateHighMost versatile; single row
Angular contact (ACB)HighHigh (1-dir)HighMust mount in pairs for thrust both ways
4-point contactHighBoth dirModerateCompact; higher friction
Self-aligningModerateLowModerateTolerates misalignment

Load Capacity (ISO 281)

Dynamic load rating C [kN]: from catalog; basis for life calculation Static load rating C_0 [kN]: maximum load before plastic deformation (rolling contact stress < 4200 MPa)

L10 Life Calculation (ISO 281)

Basic rating life: L_10 = (C/P)^p [millions of revolutions] p = 3 (ball bearings); p = 10/3 (roller bearings)

Equivalent dynamic load: P = X F_r + Y F_a [N] X, Y = radial/axial factors from catalog (depend on F_a/F_r and F_a/C_0) For DGBB: if F_a/F_r ≤ e, P = F_r; if F_a/F_r > e, P = 0.56F_r + Y F_a

In hours: L_10h = L_10 × 10⁶ / (60 × n) where n = speed [rpm]

Modified Life (ISO 281:2007, a_ISO)

L_nm = a_1 × a_ISO × L_10

a_1 = reliability factor: L_10: a_1=1.0; L_5: a_1=0.62; L_1: a_1=0.21

a_ISO: function of κ (viscosity ratio) and fatigue load limit C_u/P κ = ν_actual / ν_1 (ν_1 = reference kinematic viscosity from chart) High κ (good lubrication) → high a_ISO → better life

Speed Limits

Reference speed n_ref [rpm]: from catalog (thermal reference speed) Limiting speed n_lim [rpm]: max mechanical speed (cage/lubricant constraint) Reduce n_ref by: cage type, lubrication type, temperature factors

ndm parameter: n × d_m [mm·rpm] where d_m = (d+D)/2 DGBB: n d_m ≤ 600,000–1,200,000 (grease); ≤ 1,500,000–2,000,000 (oil)

Preload (Angular Contact Bearings)

Preload eliminates internal clearance → removes play, increases stiffness, improves accuracy

Fixed preload: springs or shims apply fixed axial force F_pre Position preload: spacers fix axial position (preload varies with temperature)

Recommended preload: F_pre = 0.005 C to 0.02 C (light to medium) Effect on life: preload adds to load P_total → shorter life; trade-off vs. stiffness

Bearing Fits

Inner ring (rotating inner ring is standard): Shaft fit: interference (k5, m5, n5 for normal-heavy loads) Inner ring rotates → must be interference fit to prevent creep

Outer ring: Housing fit: sliding (H7, G7 for normal; P7 for heavy shock) Fixed outer ring → transition fit acceptable; floating end → sliding fit

Clearance vs. preload: Standard: CN (C0) clearance → slight internal play before mounting Light interference mounting → C2 (less than CN) or CN preloaded to zero play

Lubrication

Grease: 70–80% of all bearing applications Fill factor: 30–50% of bearing free space (over-packing causes overheating) Re-lubrication interval: L_10 / 5 to L_10 / 3 typical

Oil (circulating or bath): high speed or high temperature Oil viscosity at operating temperature: ν_min from ISO chart for bearing size and speed

SKF/FAG Catalog Usage

  1. Determine bore d, OD D, width B (series 6000, 6200, 6300, 7000, 7200)
  2. Read C and C_0 from catalog
  3. Compute P = XF_r + YF_a
  4. Calculate L_10h — compare to design life requirement
  5. Check speed vs. n_ref
  6. Specify fit and lubrication

Common Series

SeriesBore rangeNotes
600010–150 mmExtra light; low noise
620010–150 mmLight series; most common
630010–150 mmMedium; higher C
720010–150 mmAngular contact 15°
730010–150 mmAngular contact 25°

Output

Provide: bearing designation (e.g., SKF 6210), C [kN], C_0 [kN], P [N], L_10h [hours] vs. design target, speed [rpm] vs. n_ref, fit specification (shaft k5, housing H7), lubrication type and interval.

Security

  • Security scanPassed, 90 of 100Pattern checks on the skill's files.
  • Model reviewPassed

Quality evaluation

  • Task evaluationNot runNo evaluation yet. Run one in Skill Studio.

Source

Popularity

7-day trend score
0

Not refreshed yet.

Works with

Any agent vskill installs to: 56 targets in all. These 39 have a page on this site.

  • Claude Code
  • Cursor
  • GitHub Copilot
  • Windsurf
  • Codex
  • Gemini CLI
  • Cline
  • Amp
  • Roo Code
  • Goose
  • Continue
  • Kilo Code
  • Junie
  • Trae
  • OpenHands
  • Qwen Code
  • AI Agent
  • Tabnine Chat
  • Sourcegraph Cody
  • Amazon Q
  • Firebase Genkit
  • Sweep
  • Devin
  • Phind
  • Mentat
  • Claude Desktop
  • Aider
  • GPT Pilot
  • Plandex
  • bolt.new
  • v0
  • Replit Agent
  • Anse
  • TypingMind
  • BetterChatGPT
  • LibreChat
  • Warp AI
  • Pieces
  • Fig AI
Embed badge
vskill VERIFIED badge
[![vskill VERIFIED](https://verified-skill.com/api/v1/skills/mp-ai-20/mechanical-engineering-skills/ball-bearing-selection/badge)](https://verified-skill.com/skills/mp-ai-20/mechanical-engineering-skills/ball-bearing-selection)

Something wrong with this skill or its page? Tell us.